Nec MM2000 Manual do Utilizador

MM2000User’s ManualMultimedia Switcher for DLP Cinema® ProjectorNEC Viewtechnology, Ltd.

21-1. Features• 3D Motion Adaptive I/P Conversion Supports a Multi-directional Filter for HDTVDiffering from the conventional 3D Motion Adaptive inter

31. Introduction1-2. What’s in the Box?The accessory contents are as follows:• Multimedia Switcher (MM2000)• Ferrite clamp core (for Power cable / RG

41. Introduction1-3. Getting to Know Your Switcher1-3-1. Front of the SwitcherControl panel(See page 5)HandlesVentilation (inlet)1-3-2. Rear of the Sw

51. Introduction1-3-3. Control Panel123546910781. LCD ScreenThe liquid crystal display screen shows the condition orthe error message of the Switcher.

61. Introduction1-3-4. Control Terminals/Image Output Terminals123456781. LAN port (RJ-45)This port is used for linked control from the NC series proj

71. Introduction1-3-5. Image Input terminalsYou can mount various interface boards to any position you want among slots 1 to 4. For removal and instal

81. Introduction1-3-6. Option Boards MM-SDI Interface Board (Option)The SDI signal input board is available as an option.(1) (2) (3) (4)(1) STATUS Ind

91. Introduction MM-DVI Interface Board (Option)The DVI signal input board is available as an option.(1) (2)(1) DVI-D Input Connector (DVI-D 24 Pin)Us

102.Installation2-1. Making ConnectionsNOTEWhen using with a notebook PC, be sure to connect between the Switcher and the notebook PC before turningon

112. Installation2-2. Connecting Your ProjectorConnect this unit and the projector as shown below. Connect the DVI-D A input terminal (DVI-A) on the

Important InformationPrecautionsPlease read this manual carefully before using your MM2000Switcher and keep the manual handy for future reference.Your

122. Installation2-3. Connecting to the Image Input TerminalsThis Switcher has two interface boards, MM-VIDEO and MM-RGB as standard equipment. See pa

132. Installation2-4. Install the Option Boards and Expand the Image Input TerminalsFour types of option boards are available for the Switcher.Please

142. Installation2-5. Connecting to a NetworkConnect various control terminals as required.The switcher is provided with a LAN port (RJ-45) as standar

152. Installation2-6. Connecting the Supplied Power CableConnect the supplied power cable to the Switcher.First connect the supplied power cable’s thr

163.Projecting an ImageSpecify “Title select” from the projector to project images of a device connected to this unit. Refer to the Projector User’sMa

173. Projecting an Image3-2. Turning off the SwitcherTo turn off the Switcher:First press the POWER (ON/STAND BY) button on the Switchercabinet for a

184.LCD Menu4-1. Basic operation from LCD screen menuWith the LCD screen menu, you can display various information about this unit.4-1-1. Screen displ

194. LCD Menu4-1-2. Operating menusPreparation: Turn on the unit (See page 16).1Press the MENU button.A menu is displayed on the LCD screen.2Press the

205-1. Cleaning the Cabinet1Turn off the Switcher before cleaning.2Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild det

216.Appendix6-1. TroubleshootingBefore asking for repair, please check your connection, settings and operation once again. For control of the switcher

E-2CAUTION• When switching off the Main Power switch, set the Switcherto the standby mode beforehand. Doing so can causedamage to the Switcher.• Do n

226. Appendix6-1-2. When the PC Screen Does Not Project ProperlyCheck the following if the screens do not project properly when projecting while conne

236. Appendix6-3. Compatible input signal listSignalNTSCPALPAL60SECAMVESAVESAVESAVESAVESAVESAVESAVESAVESAVESAVESAVESAVESAVESAVESAVESAVESAVESAVESAVESAV

246. Appendix6-4. SpecificationsModel NumberImage InputImage Input(Optional board specifications)Image output Image signal processing Input SlotMM-VID

256. AppendixPC CardFunctionEnvironmentStorage EnvironmentPower supplyDimensionsNet weightRegulationsOptional componentsType II x 1 (For service perso

266. AppendixCaracteristiques techniquesNuméro de modèleEntrée d'image Entrée d'image (Caractéristiques de la carte en option)Sortie d'

276. AppendixCarte PCFonctionEnvironnementEnvironnement de stockageAlimentation électriqueDimensionsPoids netRéglementationsComposants optionnelsType

286. AppendixTechnische DatenModellnummerBildeingangBildeingang (Technischen Daten der optionalen Karte)BildausgangBildsignalbearbeitungEingangsschlit

296. AppendixPC-KarteFunktionUmgebungLagerungsumgebungStromversorgungMaßeNettogewichtAngewandte Optionale KomponentenTyp II x 1 (Für servicepersonal)S

306. Appendix6-5. Cabinet DimensionsUnits = mm

© NEC Viewtechnology, Ltd. 2006 Printed in JapanVer.1 08/06

Informations importantesPrécautionsVeuillez lire ce manuel avec attention avant d’utiliser votrecommutateur MM2000 et gardez ce manuel à portée de mai

7N8P6981Printed on recycled paperMM2000 User’s Manual

F-2Important InformationPrécautions contre les risques d’incendie etd’électrocution• Assurez-vous que la ventilation est suffisante et que lestrous d’

G-1Important InformationWichtige InformationenVorsichtsmaßnahmenLesen Sie sich dieses Handbuch bitte sorgfältig durch, bevorSie den MM2000 Switcher be

G-2Important InformationACHTUNG• Setzen Sie den Schalter in den Standby-Modus, bevorSie den Hauptnetzschalter ausschalten. Andernfalls kannder Schalt

G-3Important Information(MEMO)

Table of Contents11.Introduction ..................... 21-1. Features ......