NEC Express5800/R110f-1E Manual do Utilizador

1 Appendix B : raidcmd Command Reference This chapter describes commands of the raidcmd. Notice on specifying Physical Device number The -p option

10 Command Parameter Description [-y] Creates the Logical Drive immediately without displaying the message of confirming that the Logical Drive may

11 mklds [Overview] Creates a Logical Drive with simple parameter settings. [Format] raidcmd mklds -c=<controller> -p=<physicaldevice1>,

12 mkscd [Overview] Creates an SSD Cache Drive. [Format] raidcmd mkscd -c=<controller> -p=<physicaldevice1> [,<physicaldeviceX>, .

13 oplist [Overview] Displays the list of operations performed in a RAID Controller and their progresses. [Format] raidcmd oplist [Description] Disp

14 optctrl [Overview] Allows you to set optional parameters of a RAID Controller. [Format] raidcmd optctrl -c=<controller> {-ip={high | middle

15 optld [Overview] Allows you to set optional parameters of a Logical Drive. [Format] raidcmd optld -c=<controller> -l=<logicaldrive> -

16 property [Overview] Displays the properties of RAID Controllers, Disk Arrays, Logical Drives and/or Physical Devices. [Format] raidcmd property –

17 rebuild [Overview] Starts or stops Rebuild. [Format] raidcmd rebuild -c=<controller> -p=<physicaldevice> -op={start|stop} Command Pa

18 refresh [Overview] Refreshes the battery connected to the RAID Controller [Format] raidcmd refresh -c=<controller> [-y] Command Parameter

19 refreshs [Overview] Refreshes the batteries connected to the RAID Controllers which support the Refresh Battery function. [Format] raidcmd refres

2 ccs [Overview] Starts Consistency Check of Logical Drives in the RAID Controllers in which Patrol Read is disabled or not supported. [Format] raid

20 rescan [Overview] Update the RAID System management information of the Universal RAID Utility. [Format] raidcmd rescan [Description] This command

21 runmode [Overview] Changes the RAID System Management Mode of the raidcmd. [Format] raidcmd runmode [-md={a|s}] Command Parameter Description [

22 sbuzzer [Overview] Stops the Buzzer on a RAID Controller. [Format] raidcmd sbuzzer -c=<controller> Command Parameter Description -c=<c

23 slotlamp [Overview] Turns on or off the DISK lamp of the computer or enclosure in which Physical Devices are installed. [Format] raidcmd slotlamp

24 stspd [Overview] Changes the status of a Physical Device to online or failed forcibly. [Format] raidcmd stspd -c=<controller> -p=<physic

25 (no command) [Overview] Displays the version of Universal RAID Utility and the RAID System Configuration as a Tree View. [Format] raidcmd [Descri

3 delld [Overview] Deletes a Logical Drive. [Format] raidcmd delld -c=<controller> -l=<logicaldrive> [-y] Command Parameter Descriptio

4 delscd [Overview] Deletes an SSD Cache Drive. [Format] raidcmd delscd -c=<controller> -l=<logicaldrive> [-y] Command Parameter Descr

5 econfig [Overview] Configures a RAID System with a RAID Controller easily. [Format] raidcmd econfig [Description] Executes easy configuration whic

6 help [Overview] Displays the help of raidcmd. [Format] raidcmd help <subcommand> Command Parameter Description <subcommand> Specify

7 hotspare [Overview] Makes or removes a Hot Spare. [Format] raidcmd hotspare -c=<controller> -p=<physicaldevice> -mr={make [-a=<disk

8 init [Overview] Starts or stops Initialize. [Format] raidcmd init -c=<controller> -l=<logicaldrive> -op={start|stop} [-im={full|quick}

9 mkldc [Overview] Creates a Logical Drive with advanced parameter settings. [Format] Making a Logical Drive having RAID Level of RAID 0, RAID 1, RA