NEC Express5800/R120f-1M Manual do Utilizador

Appendix B : raidcmd Command Reference This chapter describes commands of the raidcmd. Notice on specifying Physical Device number The -p option for

mkldc [Overview] Creates a Logical Drive with advanced parameter settings. [Format] Making a Logical Drive having RAID Level of RAID 0, RAID 1, RAID

Command Parameter Description -rl={0 | 1 | 5 | 6 | 10 | 50 | 60 } Specify the RAID Level of the Logical Drive to be created as follows: 0 : RAID 0 1 :

mklds [Overview] Creates a Logical Drive with simple parameter settings. [Format] raidcmd mklds -c=<controller> -p=<physicaldevice1>, <

mkscd [Overview] Creates an SSD Cache Drive. [Format] raidcmd mkscd -c=<controller> -p=<physicaldevice1> [,<physicaldeviceX>, ... ,

oplist [Overview] Displays the list of operations performed in a RAID Controller and their progresses. [Format] raidcmd oplist [Description] Displays

optctrl [Overview] Allows you to set optional parameters of a RAID Controller. [Format] raidcmd optctrl -c=<controller> {-ip={high | middle | l

optld [Overview] Allows you to set optional parameters of a Logical Drive. [Format] raidcmd optld -c=<controller> -l=<logicaldrive> -cm={

property [Overview] Displays the properties of RAID Controllers, Disk Arrays, Logical Drives and/or Physical Devices. [Format] raidcmd property –tg=

rebuild [Overview] Starts or stops Rebuild. [Format] raidcmd rebuild -c=<controller> -p=<physicaldevice> -op={start|stop} Command Parame

refresh [Overview] Refreshes the battery connected to the RAID Controller [Format] raidcmd refresh -c=<controller> [-y] Command Parameter Desc

ccs [Overview] Starts Consistency Check of Logical Drives in the RAID Controllers in which Patrol Read is disabled or not supported. [Format] raidcmd

refreshs [Overview] Refreshes the batteries connected to the RAID Controllers which support the Refresh Battery function. [Format] raidcmd refreshs [

rescan [Overview] Update the RAID System management information of the Universal RAID Utility. [Format] raidcmd rescan [Description] This command col

runmode [Overview] Changes the RAID System Management Mode of the raidcmd. [Format] raidcmd runmode [-md={a|s}] Command Parameter Description [-md={

sbuzzer [Overview] Stops the Buzzer on a RAID Controller. [Format] raidcmd sbuzzer -c=<controller> Command Parameter Description -c=<contro

slotlamp [Overview] Turns on or off the DISK lamp of the computer or enclosure in which Physical Devices are installed. [Format] raidcmd slotlamp -c=

stspd [Overview] Changes the status of a Physical Device to online or failed forcibly. [Format] raidcmd stspd -c=<controller> -p=<physicalde

(no command) [Overview] Displays the version of Universal RAID Utility and the RAID System Configuration as a Tree View. [Format] raidcmd [Descriptio

delld [Overview] Deletes a Logical Drive. [Format] raidcmd delld -c=<controller> -l=<logicaldrive> [-y] Command Parameter Description -c

delscd [Overview] Deletes an SSD Cache Drive. [Format] raidcmd delscd -c=<controller> -l=<logicaldrive> [-y] Command Parameter Descripti

econfig [Overview] Configures a RAID System with a RAID Controller easily. [Format] raidcmd econfig [Description] Executes easy configuration which c

fwup [Overview] Updates the RAID Controller firmware. [Format] raidcmd fwup –c= <controller> -f=<firmware image filepath> [-ocr={yes|no}]

help [Overview] Displays the help of raidcmd. [Format] raidcmd help <subcommand> Command Parameter Description <subcommand> Specify the

hotspare [Overview] Makes or removes a Hot Spare. [Format] raidcmd hotspare -c=<controller> -p=<physicaldevice> -mr={make [-a=<diskarr

init [Overview] Starts or stops Initialize. [Format] raidcmd init -c=<controller> -l=<logicaldrive> -op={start|stop} [-im={full|quick}] [