NEC SigmaBlade AD106a Guia do Utilizador Página 132
- Página / 162
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
8-8 Troubleshooting
Virtual LCD indications when STATUS lamp is flashing in amber
On-screen message Description Action
HDD X Fault An error was detected in hard
disk drive installed in Storage and
I/O Blade.
X: Indicates slot number
containing the failing hard disk
drive with 0-origin number.
Contact your service representative.
E-Keying Error In the Blade Enclosure,
combination of installation
locations of Storage and I/O
Blade, mezzanine card, and
switch module is not correct.
Thus, an unconformity of
interface signal was detected and
the CPU blade failed to power on.
Refer to the User's Guide of Blade
Enclosure for correct installation
locations.
If the same error persists, contact your
service representative.
Location Error In the Blade Enclosure, the
installation location of Storage
and I/O Blade is incorrect, or the
installation locations of the fan
and Storage and I/O Blade are
incorrect. Thus, the CPU blade
failed to power on.
Refer to the User's Guide of Blade
Enclosure to check if the Storage and I/O
Blade is installed in correct location.
Check the installation locations of the fan
and Storage and I/O Blade.
If the same error persists, contact your
service representative.
Cooling Error
In the Blade Enclosure, the
number of fans installed is
insufficient or the installed fan is
faulty. Thus, the CPU blade failed
to power on due to insufficient
cooling power.
AmbientTempAlm07
A high temperature warning was
detected in Storage and I/O
Blade.
AmbientTempAlm00 A low temperature warning was
detected in Storage and I/O
Blade.
Check if fans in Blade Enclosure work
normally.
Refer to the User’s Guide of the Blade
Enclosure to make sure that the
sufficient number of fans are installed in
correct locations.
Check if the fans and Storage and I/O
Blade are installed in correct locations.
Check if the ambient temperature of
installation location satisfies the
operation guarantee condition.
If the same error persists, contact your
service representative.
BB +1.0v Alm XX
BB +3.3v Alm XX
BB +5v Alm XX
BB +0.9vs Alm XX
BB +1.0vs Alm XX
BB +1.8vs Alm XX
BB +3.3vs Alm XX
BB +5vs Alm XX
BB +12vs Alm XX
Battery Alm XX
A voltage warning was detected
on Storage and I/O Blade.
XX=07: Upper limit warning
XX=00: Lower limit warning
Contact your service representative.
- NEC Express5800 Series 1
- Storage and I/O Blade AD106a 1
- User's Guide 1
- SAFETY INDICATIONS 3
- Attentions 4
- Prohibited Actions 4
- Mandatory Action 4
- Trademarks 6
- ABOUT THIS USER'S GUIDE 8
- IN THE PACKAGE 9
- CONTENTS 10
- Chapter 1 13
- SAFETY NOTES 14
- Do not step on the cable 15
- FOR PROPER OPERATION 17
- TRANSFER TO THIRD PARTY 19
- DISPOSAL AND CONSUMABLES 20
- USER SUPPORT 21
- Advice for Health 22
- Chapter 2 23
- OVERVIEW 24
- STANDARD FEATURES 25
- Front View 26
- Internal View 27
- External View 28
- Lamp Indications 30
- STATUS Lamp 31
- LAN (1 - 2) Link/Access Lamps 32
- DISK ACCESS Lamp 32
- Device Identification 34
- Chapter 3 35
- Check of MAC Address 36
- Installation Order 37
- SIGMABLADE-M 38
- Installing in Blade Enclosure 39
- Joint bracket for AD106a 42
- Installation and Removal 43
- IMPORTANT: 44
- Chapter 4 45
- RAID SYSTEM CONFIGURATION 46
- RAID Levels 49
- Removed physical drive 55
- Migration only 55
- Migration with addition 55
- Before Using WebBIOS 58
- Using WebBIOS 61
- Main Menu 62
- WebBIOS Menu 63
- Controller Properties 65
- How to change setting value 69
- Scan Devices 70
- Virtual Drives 71
- Physical Drive Properties 73
- 3. Click [Go] 73
- Configuration Wizard 75
- Controller Selection 75
- Physical View / Logical View 75
- Configuring Virtual Drive 77
- DG is added to Span 80
- Configure SPAN 85
- [Accept] 87
- Parameters for VD Definition 90
- Operation of Various Features 93
- Manual Rebuild 95
- Setting Hot Spare 99
- "DED HOTSPARE" 100
- Reconstruction 102
- Slow Initialize 105
- Number and ID 106
- Setting of Priority 107
- Chapter 5 109
- Setup of teaming 110
- Network Driver 111
- Optional Network Board Driver 111
- Setting WOL 111
- Setting Receive Side Scaling 112
- TCP Chimney Offload 113
- Receive-side Scaling 113
- NetDMA 113
- SETTING FOR SOLVING PROBLEMS 115
- UPDATING THE SYSTEM 118
- Chapter 6 119
- Chapter 7 121
- SYSTEM DIAGNOSTICS 122
- RELOCATING/STORING THE UNIT 123
- Chapter 8 125
- SYSTEM VIEWERS 126
- ERROR MESSAGES 127
- 8-4 Troubleshooting 128
- Troubleshooting 8-5 129
- Error Messages on Virtual LCD 130
- Troubleshooting 8-7 131
- 8-8 Troubleshooting 132
- SOLVING PROBLEMS 133
- Fail to power-off: 134
- Fail to start OS: 135
- Problems with Windows 137
- Server 2003 x64 Editions: 139
- Server 2003 R2 142
- COLLECTING EVENT LOG 146
- MAINTENANCE TOOLS 146
- Chapter 9 147
- ANTI-STATIC MEASURES 149
- PREPARATION FOR INSTALLATION 151
- Mezzanine Card 152
- Hard Disk Drive 157
- Appendix A 161
- A-2 Specifications 162
Manuais e produtos relacionados com Controladores RAID NEC SigmaBlade AD106a
Controladores RAID NEC N8103-89 Manual do Utilizador
(128 páginas)
(128 páginas)
Indesit DVSR 5 manuals
Owner’s manuals and user’s guides for Dishwashers Indesit DVSR 5.
We providing 1 pdf manuals Indesit DVSR 5 for download free by document types: Instruction for Use
Comentários a estes Manuais