NEC SigmaBlade AD106a Guia do Utilizador Página 155
- Página / 162
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Upgrading Your Storage and I/O Blade 9-9
8. From top of the Storage and I/O Blade, position the connector of the mezzanine card so
that it aligns the connector of the mezzanine card slot, and insert the mezzanine card
straight into the slot.
IMPORTANT:
Do not make your body contact with the terminals on the board.
Some malfunction may occur if the board is installed with dirt
and/or oil adhering to the terminals.
Insert the mezzanine card straight into the connector. The terminal
or connector may be damaged if it is inclined.
If the board cannot be installed securely, remove the board once and
then install it again. Adding excess force to the board may cause the
board to be damaged.
9. Push the connector portion of the mezzanine card with fingers firmly to connect the card
to the slot.
10. Tighten the fixing screws to fix the mezzanine card to the Storage and I/O Blade.
11. Install the top cover having been removed.
12. Secure the top cover with two screws.
13. Secure the joint bracket for AD106a having been removed with a single screw.
14. Install the Storage and I/O Blade having been removed to the Blade Enclosure.
15. Turn on the power of the CPU blade. Make sure that any error messages associated with
the board do not appear on the POST screen.
Refer to the User's Guide of CPU Blade for details of POST error messages.
16. Run BIOS SETUP of CPU blade, and select [Advanced] – [Reset Configuration Data] on
the [Advanced] menu and set to [Yes].
This is required to update the hardware update information. Refer to the User's Guide of
CPU Blade for details.
17. Run the BIOS configuration utility of the installed board to provide setup for the board.
The existence of the utility and its start and operation procedures vary depending on the
type of the board. Refer to the documentation coming with the board for details.
Type I
Type II
- NEC Express5800 Series 1
- Storage and I/O Blade AD106a 1
- User's Guide 1
- SAFETY INDICATIONS 3
- Attentions 4
- Prohibited Actions 4
- Mandatory Action 4
- Trademarks 6
- ABOUT THIS USER'S GUIDE 8
- IN THE PACKAGE 9
- CONTENTS 10
- Chapter 1 13
- SAFETY NOTES 14
- Do not step on the cable 15
- FOR PROPER OPERATION 17
- TRANSFER TO THIRD PARTY 19
- DISPOSAL AND CONSUMABLES 20
- USER SUPPORT 21
- Advice for Health 22
- Chapter 2 23
- OVERVIEW 24
- STANDARD FEATURES 25
- Front View 26
- Internal View 27
- External View 28
- Lamp Indications 30
- STATUS Lamp 31
- LAN (1 - 2) Link/Access Lamps 32
- DISK ACCESS Lamp 32
- Device Identification 34
- Chapter 3 35
- Check of MAC Address 36
- Installation Order 37
- SIGMABLADE-M 38
- Installing in Blade Enclosure 39
- Joint bracket for AD106a 42
- Installation and Removal 43
- IMPORTANT: 44
- Chapter 4 45
- RAID SYSTEM CONFIGURATION 46
- RAID Levels 49
- Removed physical drive 55
- Migration only 55
- Migration with addition 55
- Before Using WebBIOS 58
- Using WebBIOS 61
- Main Menu 62
- WebBIOS Menu 63
- Controller Properties 65
- How to change setting value 69
- Scan Devices 70
- Virtual Drives 71
- Physical Drive Properties 73
- 3. Click [Go] 73
- Configuration Wizard 75
- Controller Selection 75
- Physical View / Logical View 75
- Configuring Virtual Drive 77
- DG is added to Span 80
- Configure SPAN 85
- [Accept] 87
- Parameters for VD Definition 90
- Operation of Various Features 93
- Manual Rebuild 95
- Setting Hot Spare 99
- "DED HOTSPARE" 100
- Reconstruction 102
- Slow Initialize 105
- Number and ID 106
- Setting of Priority 107
- Chapter 5 109
- Setup of teaming 110
- Network Driver 111
- Optional Network Board Driver 111
- Setting WOL 111
- Setting Receive Side Scaling 112
- TCP Chimney Offload 113
- Receive-side Scaling 113
- NetDMA 113
- SETTING FOR SOLVING PROBLEMS 115
- UPDATING THE SYSTEM 118
- Chapter 6 119
- Chapter 7 121
- SYSTEM DIAGNOSTICS 122
- RELOCATING/STORING THE UNIT 123
- Chapter 8 125
- SYSTEM VIEWERS 126
- ERROR MESSAGES 127
- 8-4 Troubleshooting 128
- Troubleshooting 8-5 129
- Error Messages on Virtual LCD 130
- Troubleshooting 8-7 131
- 8-8 Troubleshooting 132
- SOLVING PROBLEMS 133
- Fail to power-off: 134
- Fail to start OS: 135
- Problems with Windows 137
- Server 2003 x64 Editions: 139
- Server 2003 R2 142
- COLLECTING EVENT LOG 146
- MAINTENANCE TOOLS 146
- Chapter 9 147
- ANTI-STATIC MEASURES 149
- PREPARATION FOR INSTALLATION 151
- Mezzanine Card 152
- Hard Disk Drive 157
- Appendix A 161
- A-2 Specifications 162
Manuais e produtos relacionados com Controladores RAID NEC SigmaBlade AD106a
Controladores RAID NEC N8103-89 Manual do Utilizador
(128 páginas)
(128 páginas)
Indesit DVSR 5 manuals
Owner’s manuals and user’s guides for Dishwashers Indesit DVSR 5.
We providing 1 pdf manuals Indesit DVSR 5 for download free by document types: Instruction for Use
Comentários a estes Manuais